Braun ThermoScan IRT 6510 Uživatelský manuál stáhnout pdf (Strana 6)

8 9

English

Changing the temperature scale

If you wish to change the temperature scale of your thermometer:

Make sure the thermometer is turned off.

Press and hold down the Power button . After about 3 seconds

the display will show this sequence: ° C / SET / ° F / SET ...

Release the Power button when the desired temperature scale is shown.

There will be a short beep to conﬁrm the new setting, then the thermometer

is turned off automatically.

Replacing the batteries

The thermometer is supplied with two 1.5 V type AA (LR 06) batteries.

For best performance, we recommend Duracell

alkaline batteries.

Insert new batteries when the battery symbol appears on the display.

Open the battery compartment. Remove the batteries and replace with new

batteries, making sure the poles are in the right direction.

Snap battery door into place.

The

moScan

15 sec

This thermometer includes a convenient night light

to illuminate the display in a dim environment.

The light will turn on when you press any button. It

will stay on until the thermometer is inactive for up

to 15 seconds even after temperature is taken.

The probe tip is the most delicate part of the thermometer. It must be

clean and intact to ensure accurate readings. If the thermometer is ever

accidentally used without a lens ﬁlter, clean the probe tip as follows:

Very gently wipe the surface with a cotton swab or soft cloth moistened

with alcohol. After the alcohol has completely dried out, you can put a new

lens ﬁlter on and take a temperature measurement.

If the probe tip is damaged, please contact Consumer Relations.

Use a soft, dry cloth to clean the thermometer display and exterior. Do not use abrasive cleaners.

Never submerge this thermometer in water or any other liquid. Store thermometer and lens ﬁlters

in a dry location free from dust and contamination and away from direct sunlight.

Additional lens ﬁlters (LF 40) are available at most stores carrying Braun ThermoScan.

To protect the environment, dispose of the product and empty batteries at

your retail store or at appropriate collection sites according to national or

local regulations.

Calibration

The thermometer is initially calibrated at the time of manufacture. If this thermometer is used according to

the use instructions, periodic re-adjustment is not required. If at any time you question the accuracy of

temperature measurements, please contact Consumer Relations.

Manufacturing date is given by the LOT number located inside the battery compartment. The ﬁrst three (3)

digits after LOT represent the Julian date that the product was manufactured and the next two (2) digits

represent the last two numbers of the calendar year the product was manufactured. The last identiﬁers are

the letters that represent the manufacturer.

An example: LOT 11614KTC, this product has been manufactured on the 116th day of the year 2014.

Errors and troubleshooting

Situation

No lens ﬁlter is attached.

The thermometer probe was not

positioned securely in the ear.

An accurate measurement

was not possible.

POS = position error

Ambient temperature is not within

the allowed operating range

(50 – 104 °F or 10 – 40 °C ).

Temperature taken is not within

typical human temperature range

(93.2 – 108 °F or 34 – 42.2 °C).

HI = too high

LO = too low

System error – self-check display ﬂashes

continuously and will not be followed by

the ready beep and the ready symbol.

If error persists,

If error still persists,

Battery is low, but thermometer will

still operate correctly.

Battery is too low to take correct

temperature measurement.

Error Message

Solution

Attach new, clean lens ﬁlter.

Take care that the positioning of the

probe is correct and remains stable.

Replace lens ﬁlter and reposition.

Press Start button to begin a new

measurement.

Allow the thermometer to remain for

30 minutes in a room where the

temperature is between 50 and 104 °F

or 10 and 40 °C.

Make sure the probe tip and lens are clean

and a new, clean lens ﬁlter is attached.

Make sure the thermometer is properly

inserted. Then, take a new temperature.

Wait 1 minute until the thermometer turns

off automatically, then turn on again.

... reset the thermometer by removing the

batteries and putting them back in.

… please contact Customer Service.

Insert new batteries.

Available only in

IRT 6510

Care and cleaning

Night light feature

1 2 3 4 5 6 7 8 9 10 11 ... 19 20

Komentáře k této Příručce

Žádné komentáře

Braun ThermoScan IRT 6510 Uživatelský manuál Strana 6

Komentáře k této Příručce